Search results

Gave the truck a quick bath today and took a few more shots of the rollpan from different angles. Can't wait to get the front end blacked out and remove the side moulding in the next couple weeks.

Same wheels, tires, etc, etc. that I had on before. Only part changed were the spindles. Before the install, the wheels sat flush with the fenders. Now they're out about a 1/4" on both sides. Is there a revised part/part number maybe?

Looks great. Light output looks good considering how dark the lens' look in the pictures.

You can get a normal key cut for these vehicles that will still start the vehicle, but there is still an anti-theft system that needs a bypass module installed. The system is built into the ignition cylider rather than the key itself, and activates when the ignition switch is turned.

Like OMAR stated above, the truck doesn't use the older VATS system, but uses PKII instead, so you still need an override module. For the tach, you can use any of the fuel injector pulse wires as your tach source. Each injector will have two wires; one that is a common color on all eight...

I wish, but I haven't been able to find a set I really liked. I may end up ordering a set anyway later on and just tinting them with a couple light coats of black to blend in with the truck better. It's a Street Scene urethane rollpan from StylinTrucks.com I used the stock plate lights...

Thanks for the props guys:thumbsup: It's a urethane piece, so it's bolted in place. Once the tongue slides into place, the plate rests down about a 45* angle, so it's still visible.

Awesome. Welcome to the site! We have tons of cool people and info around here.

These pictures aren't great at all. I took these with the truck dirty and in my garage at night. I'll snap some more shots once I wash the truck. I installed a Sir Micheals hide-away hitch behind the rollpan and a flip-up liscence plate so I can still tow the boat and car trailer around. Thanks...

Just for the record; My McGaughy's spindles pushed the wheel out about a little over a 1/4" or so. May not be a big deal in most cases, but it was on mine. Also, the holes for the balljoints are just a bit small and I had to use a die grinder to remove some material in order to press in both the...

Any aftermarket stereo, whether single din or double, aren't as wide as the stock GM unit.

Nice man, I like it!

Pioneer has a firmware update for the new AVIC BT models. The latest update is the 2.0 and will take care of the slow startup process. The Pioneer units sell more than the Kenwood models do in my area. Most customers prefer the user menu and features of the newer AVIC models over the Kenwood...

You have to tag all four door trigger circuits and use diodes to isolate each door, or you can tag the domelight circuit. Using the domelight circuit will start the passive arm countdown once the delayed dome circuit shuts down. What year is your truck? 00-02 wiring is different than the 03-06...

You can use a crimp connector, but I always highly recommend soldering due to much less electrical property losses and greater reliability, especially in a constant vibration scenario like a vehicle. I've seen it thousands of times where I am troubleshooting an aftermarket component or wiring...

Welcome to the site. Your truck looks good with the wheels and more aggressive stance.

Once you have the dash bezel removed (the trim that goes around the ip, radio, hvac, etc), you can remove the steering column shroud and get to the harness from there. Locate the lt grn wire from the swc connector, strip back some of the insulation, and solder on the green wire from the...

Nice set of vehicles. Truck looks great. I've built and ran camaros most my life, always had this thing against 'stangs, but your Cobra looks nice man. Good job on both.

Welcome to the site! Sounds like a killer deal you ended up with:beerchug: Post some pics when you get a chance and let's see what you're working with.

00-06. With the key in the run position, press the accelerator pedal down fully and release three times. The next time you start the truck, the Change Oil msg will flash 5 times then go off if cleared successfully.